A device plugged into the OBD socket, which will inform you about the beginning and end of the regeneration procedure of the particle filter in your car from the VAG group. The device allows you to reduce fuel consumption and extend the life of the DPF due to its proper operation. In addition, the proper operation of the DPF filter protects the engine as well as the turbocharger.
-
Dioed for DPF control -
Sale!Brak na magazynie
New Genius + New Trasdata Slave JOINT ACTIVATION - FULL - kit from DIMSPORT Kit includes:- NEW GENIUS Hardware
- HASP Key
- Protocols NG: Full protocols
- NEW TRASDATA Hardware
- Protocols NT: Full protocols
-
A new product from Alientech- One device with a choice of protocols tailored to specific vehicle groups and reading methods - OBD/ Bench&Boot If you have a previous KESSv2 or K-TAG device please contact us. For existing Alientech users, there is an exchange program that allows you to receive a discount of up to 95% New device -> lower annual subscriptions. From now on, the cost of annual subscription for Master version is 1190 EUR net regardless of the number of protocols. For Slave version it is 590 EUR net. -
Cable FLEX Bench BMW ZF8HP TCU
Bench cable for ZF8HP, for reading/writing Auto gearbox TCU/flash.Allows easy connections between a tool and BMW ZF8HP TCUs.
The ABRITES VIN Reader is a standalone device which allows you to read the vehicle’s identification number with the click of a button. This Bluetooth-enabled interface is compatible with nearly all vehicle brands on the market. It allows you to connect to the vehicle and read the VIN numbers in it via the OBDII port. Within 30 seconds the VIN Reader shows the identification numbers, then cross-checks it against a couple of databases for stolen vehicles, which ensures safety and security, both for professionals and for end users.
Adapter BCM 2-Keytool PLUS / MINI PROG / VVDI PROG
BCM 2 adapter that allows you to read data from protected BCM 2 modules found in Audi.Included are:
- xdnp63 needle adapter
- xdnp64 needle adapter
- 4 x locking plates
- Cable for Keytool PLUS / MINI PROG
- Cable for VVDI PROG
- Cable for soldering
- 6 x mounting screws
- Audi 2013-2019 A4, A5, Q5 (list of supported SW versions can be found directly in VVDI PROG/MINI/PLUS)
- Audi 2013-2019 A6, A7, A8 (list of supported SW versions can be found directly in VVDI PROG/MINI/PLUS)
The adapter is used to read RENESAS (M32, M32R, M32Rx) F34NTA13 engine controllers. It allows the NEW TRASDATA device to be connected to the ECU.
TEMIC bench controller connection adapter is a replacement for Alientech: 144300K251, Dimsport: F32GN053 cable To connect requires OBD2 cable for Kess: 144300K249 or New Genius: F32GN051Brak na magazynie
All FCA vehicles after 2018 are equipped with a SGW security gateway module to prevent attacks on the vehicle's network via the CAN bus. Direct connection to the OBD II-16 connector does not always give the required results-you can read errors but not clear them, you cannot program the controllers as well as make adaptations/adjustments, etc. In the case of this problem, you can bypass the SGW (Security Gateway) using the presented adapter so that full communication functionality is available.Brak na magazynie
OBDSTAR adapter designated P003 designed to work with drivers using devices such as:- X300 DP PAD
- X300 DP PLUS
- X300 series
- KM DP PLUS
Articulating Arm Adapter FLEX for MAGK00030.V2 FLX4.10.1
The adapter will allow you to attach the articulated arm to any BMD frame. When combined with the articulated arm from the link below, it enables connecting BDM adapters to the FLEX device without the need to purchase the entire frame.
