-
The DCU17CV51 cable can be used to reprogram the ACM module on JCB engines. Length: 2.5 m -
Oferta ta dotyczy usługi odblokowania pełnej mocy quada/motocykla/ATV/UTV itp. lub podniesienia mocy. Przed zakupem prosimy o kontakt pod adresem mailowym j.waskiewicz@ms-group.pl bądź numerem +48 577-446-404 przez WhatsApp w celu potwierdzenia możliwości wykonania usługi oraz wyceny. -
Adapter FTDI2232 UART ver.3.0
Universal adapter for interfacing with microcontrollers via UART, MBUS.
The board has the following outputs: DTR, DTS, DT2,TX, RX, VCC (the adapter allows you to supply this output with any voltage up to 36 V applied to the DC 2 mm input), GND, 3.3 V (voltage from the USB port via a stabilizer), 5 V (voltage from the USB port), MBUS (enabled by a jumper on the board). Jumper for switching MBUS mode. Reset button is used to reset the FTDI2232H microcontroller to its original state. Currently supported by: 1. license 22 Cypress/Fujitsu/Spansion MB91F0xx/S6J3xx MCU UART 2. license 48 Cypress/Fujitsu/Spansion 96Fxx MCU UART 3. license 55 Renesas RH850 R7F701xxx MCU UART 4. license 59 - Renesas V850 MCU
Jaltest diagnostic cable KOMATSU JDC536A The accessory cable for the Jaltest diagnostic tester allows connection to KOMATSU construction machines Technical Data Link version V8.1/V9 Length 28-30 cm
Oferta ta dotyczy usługi usunięcia danych/ informacji o wypadku w sterowniku SRS/ sterowniku poduszek powietrznych, mail: crashdata@ms-group.plBrak na magazynie
OBDSTAR CAN FD adapter is designed for diagnosing ECU systems of cars meeting with CAN FD protocols. It can be used with X300 DP Plus, X300 PRO4, and X300 DP key master for key programming and P50 for airbag reset as well. It's high performance and easy operation.
EDC17CV52 ECU Bench Cable Harness for use with a flasher tool. Used to easily connect directly to ECUs without the risk of bending pins, eliminates pinout issues, and also saves a lot of time. Length: 1.5m
Jaltest diagnostic cable for trailers KNORR-BREMSE KB4-TA JDC111A Accessory cable for the Jaltest diagnostic tester enabling connection to Knorr-Bremse KB4-TA modules in trailers.Link version V8.1/V9 Length 28-30 cm 
Scania Continental EMS S8 MPC5566 BAM Bench Cable
for use with flasher tool. Used to connect to ECUs without the risk of bending pins, and also saves a lot of time.Connection with BOOT and CFG Signals if necessary for the tool.Total Length: (Approx) 1.5m
Flex Bench Cable MG1CS002 / CP007 / CS047 for VAG ECUs – for use with a flasher tool. Allows for easy connection to ECUs without the risk of bending pins, and also saves a lot of time.
Jaltest diagnostic cable AGCO TIER 5 SISU engines JDC567A The accessory cable for the Jaltest diagnostic tester allows connection to AGCO group agricultural machines equipped with a SISU engine that meets the TIER 5 emissions standard. The JDC567A application enables quick connection to the CAN network at the turbocharger actuator. Link version V8.1/V8.4/V9 Length (mm) 300 mm
Jaltest diagnostic cable SCANIA engines 4 PIN JDC532A
The accessory cable for the Jaltest diagnostic tester allows connection to the 4-pin connector in SCANIA enginesLink version V8.1/V9 Length 28-30 cm
