-
Key programmer KEY MASTER 5 -
Brak na magazynie
OBDSTAR adapter designated P003 designed to work with drivers using devices such as:- X300 DP PAD
- X300 DP PLUS
- X300 series
- KM DP PLUS
-
Brak na magazynie
All FCA vehicles after 2018 are equipped with a SGW security gateway module to prevent attacks on the vehicle's network via the CAN bus. Direct connection to the OBD II-16 connector does not always give the required results-you can read errors but not clear them, you cannot program the controllers as well as make adaptations/adjustments, etc. In the case of this problem, you can bypass the SGW (Security Gateway) using the presented adapter so that full communication functionality is available. -
MK70 device for programming the immobiliser of Motorcycles/Quads/Watercraft.
-
Brak na magazynie
Connection cable CB021 is used for the internal CAN connection when performing key procedures on Renault and Nissan vehicles. It can also be used for mileage recalibration and module replacement on selected Renault models. -
Brak na magazynie
The JLR All Keys Lost wiring kit is essential in some cases during the key programming procedure when a direct connection to the CAN-BUS is required. The software automatically detects the platform on which the vehicle is based and prompts the customer when such a connection is required. The cable is connected between the AVDI and the OBDII cable. -
The RR029 allows mileage calibration on ATE ABS modules, on vehicles manufactured after 2020, including Megane IV ph2 and Talisman ph2 models. It is the ideal tool, solving the problem when the ABS module is replaced and the correct mileage value needs to be set. -
VN023 is another special function designed to work with the ABRITES RH850/V850 Programmer - allowing the Visteon and JCI clocks, equipped with RH850 processors, to change the waveform. -
The VN022 special function has been developed for use with the ABRITES RH850/V850 programmer to record mileage data on a non-Immo V dashboard. The new solution was developed for 8th generation VW Golf vehicles. At the same time, it makes it possible to calibrate the meter in Volkswagen, Audi, Seat, Skoda and other VAG vehicles based on the same platform. Capabilities: Recording of mileage data by the RH850 processor in Continental/VDO dashboards; Vehicles supported: VW Golf 8 and other VAG vehicles of the same generation (where the immobiliser is not integrated into the dashboard) You will need the ZN085 ABRITES RH850/V850 programmer to perform the procedure. When working with these processors, follow the wiring diagrams available in the software! AVDI, active AMS and a VN021 licence are required. -
The FN024 significantly increases the possibilities for key programming in FCA cars. With the special function FN024, we gain the possibility of preparing and programming Atmel-type keys in FCA group vehicles. -
The special function MN034 enables ALL original FBS4 Mercedes DAS (Drive Authorisation System) modules to be personalised. MN034 works closely with function MN032. Personalisation takes place via the internal CAN bus of the control modules. -
MN035 VGS4-NAG2 FBS4 virgin/personalisation via ABPROG is dedicated to working with the VGS4-NAG2 7G-Tronic TCU FBS4/DAS4. Capabilities: - reading FBS4 data from the VGS4-NAG2 module using ABPROG, - restore VGS4-NAG2 module to virgin state using ABPROG, - writing of personalised FBS4 data to the TCU using ABPROG (for holders of the MN034 special function, writing via the internal CAN-BUS is also possible). For complete information on how to use the ABRITES special features on models supported by the MN035 function, please refer to the manual HERE and HERE An ABPROG ZN030 programmer and AVDI interface, with an active AMS subscription, are required to use the MN035 function.