-
DSG cable for DL501 TCU, for reading/writing Auto gearbox TCU/flash. Allows easy connections between the flasher tool and TCUs. -
Do użytku z programatorem NEW TRASDATA. Umożliwia łatwe podłączenie do ECU bez ryzyka wyginania pinów, a także oszczędza dużo czasu. -
This adapter cable allows the use of Trasdata eGPT cables with the DFB Technology DFOX tool.
-
Bench AutoTuner Cable MD1CS003 for PSA Group Vehicles – this is a specialized cable designed for programming, diagnostics, or reading/writing data directly from the engine control unit (ECU). It is used in vehicles from Peugeot, Citroën, and other brands within the PSA Group. -
Bench AutoTuner Cable MD1CS006 for Renault - ATUBA014 – this is a specialized cable used for reading, writing, and diagnosing the engine control unit (ECU) in Renault vehicles using bench mode.
-
Cable DIMSPORT F32GN074
-
Flex Bench Cable MG1CS002 / CP007 / CS047 for VAG ECUs – for use with a flasher tool. Allows for easy connection to ECUs without the risk of bending pins, and also saves a lot of time. -
AutoTuner service mount designed for the Valeo VD56 ECU. It allows stable and secure mounting of the ECU during bench mode operations such as reading, writing, or diagnostics. -
Adapter FTDI2232 UART ver.3.0
Universal adapter for interfacing with microcontrollers via UART, MBUS.
The board has the following outputs: DTR, DTS, DT2,TX, RX, VCC (the adapter allows you to supply this output with any voltage up to 36 V applied to the DC 2 mm input), GND, 3.3 V (voltage from the USB port via a stabilizer), 5 V (voltage from the USB port), MBUS (enabled by a jumper on the board). Jumper for switching MBUS mode. Reset button is used to reset the FTDI2232H microcontroller to its original state. Currently supported by: 1. license 22 Cypress/Fujitsu/Spansion MB91F0xx/S6J3xx MCU UART 2. license 48 Cypress/Fujitsu/Spansion 96Fxx MCU UART 3. license 55 Renesas RH850 R7F701xxx MCU UART 4. license 59 - Renesas V850 MCU
Cable FLEX Bench BMW ZF8HP TCU
Bench cable for ZF8HP, for reading/writing Auto gearbox TCU/flash.Allows easy connections between a tool and BMW ZF8HP TCUs.Brak na magazynie
TEMIC bench controller connection adapter is a replacement for Alientech: 144300K251, Dimsport: F32GN053 cable To connect requires OBD2 cable for Kess: 144300K249 or New Genius: F32GN051Brak na magazynie
Adapters Bench FLEX (for connecting ECU/TCU with FLK35) FLK42B
Connectors size B, which are included in the basic FLEX device.
The FLK42B adapters allow the FLK35 coloured kit cables to be connected to the ECU and TCU modules.
Brak na magazynie
Adapters Bench FLEX (for connecting ECU/TCU with FLK35) FLK42C
Connectors size C, which are included in the basic FLEX device.
The FLK42C adapters allow the FLK35 coloured kit cables to be connected to the ECU and TCU modules.
Brak na magazynie
Adapters Bench FLEX (for connecting ECU/TCU with FLK35) FLK42D
Connectors size D, which are included in the basic FLEX device.
The FLK42D adapters allow the FLK35 coloured kit cables to be connected to the ECU and TCU modules.
Brak na magazynie
Adapters Bench FLEX (for connecting ECU/TCU with FLK35) FLK42E
Connectors size E, which are included in the basic FLEX device.
The FLK42E adapters allow the FLK35 coloured kit cables to be connected to the ECU and TCU modules.
Brak na magazynie
Adapters Bench FLEX (for connecting ECU/TCU with FLK35) FLK42F
Connectors size F, which are included in the basic FLEX device.
The FLK42F adapters allow the FLK35 coloured kit cables to be connected to the ECU and TCU modules.
Brak na magazynie
Adapters Bench FLEX (for connecting ECU/TCU with FLK35) FLK42G
The FLK42G adapters allow the FLK35 coloured kit cables to be connected to the ECU and TCU modules. Adapters with the code FLK42G are compatible with EMS3140, EMS3141, EMS3160, EMS3161, EMS3142.Brak na magazynie
Adapters Bench FLEX (for connecting ECU/TCU with FLK35)FLK42H
The FLK42H adapters allow the FLK35 coloured kit cables to be connected to the ECU and TCU modules. Adapters with code FLK42H are compatible with EDC17C49, EDC17C69, EDC7UC32, EDC7C1, EDC7C2, EDC7C3 .Brak na magazynie
Adapters Bench FLEX (for connecting ECU/TCU with FLK35) FLK42I
The adapters allow the FLK35 coloured kit cables to be connected to the ECU and TCU modules. The adapters with the code FLK42I are compatible with the MDG1 .
CABLE VOLVO ACM-MPC (DEF) KESS3/KTAG
Boot operation through the controller connector Controller on MPC chipBrak na magazynie
CABLE VOLVO ACM-SPC (ATK-EM-EU6) KESS3/KTAG/TRASDATA
Reading ACM controller in boot mode (cable bench + 1 pin boot wire after opening the controller) Cable for MPC based controllers
Brak na magazynie
CABLE SET BENCH DIMSPORT NEW TRASDATA F34NTA22-S2 A set of replacement cables that are included with the NEW TRASDATA device
CABLE SET BENCH DIMSPORT NEW TRASDATA F34NTA22-S3
A set of replacement cables that are included with the NEW TRASDATA device
CABLE SET BENCH DIMSPORT NEW TRASDATA F34NTA22-S5 A set of replacement cables that are included with the NEW TRASDATA device
CABLE SET BENCH DIMSPORT NEW TRASDATA F34NTA22-S6 A set of replacement cables that are included with the NEW TRASDATA device
EDC17C49 Bench Cable KESS3 for use with flasher tool. EDC17C49 ALL - cable equipped with a switch that supports 3 versions of connection to EDC17C49 controllers including IVECO
Universal insulated BootMode needles for reading any driver using our BDM frame with Boot extension.
Solid workmanship.
Possibility of connecting terminated with a 2mm banana cable or socket.
The price is for 1 needle. Available in 7 colors (colors are sent randomly)
MD1CE100/1 for use with a flasher tool. Used for easily connect to ECU's without the risk of bending pins, and also saves a lot of time and Time is money.
Device for opening the housing of Bosch controllers. The use of 4/6 pcs of the tool depending on the controller housing provides much faster, safer and more convenient work with the ECU without damaging or deforming the housing.Sale!
Secure Gateway Bypass Cable Autotuner ATPG050 is required to establish communication during identification/read/write operations on Renault, Dacia, Nissan & Mitsubishi vehicles equipped with a secure gateway.
EDC17CV52 Bench Cable Harnessfor use with a flasher tool. Used to easily connect directly to ECUs without the risk of bending pins, eliminates pinout issues, and also saves a lot of time.
F32GN029 cable for reading engine controllers of vehicles equipped with Valtra 16-pin connector.Sale!
EDC7UC31 for use with the KESS3 tool. Used for easily connecting to ECUs without the risk of bending pins, and also saves a lot of time and Time is money.Sale!
Cable to establish a connection with Mercedes Truck equipped with Temic ACM2.1. ECUs.Sale!Brak na magazynie
Connection cable for Mercedes Truck Continental HDEP MCM2.1 ECUs
Replacement cable used for reading DAF, MAN and SCANIA engine controllers.
